Concrete Block Calculator
Enter the wall length and height, subtract door and window openings, and choose the block face size and a waste percentage. The calculator returns the net wall area, the blocks needed exactly and to buy, the number of courses and the blocks in each course, using the nominal module of a standard eight by eight by sixteen inch block.
See also: measure wall area in feet and inches
Checked Rules used
Method note: common trade practice, not an official standard. Check the figure with your supplier.
How the concrete block calculator works
Result
How it was calculated
Fill in the fields above to see the result and every step here.
- Checked Source: TEK 04-02A Estimating Concrete Masonry Materials, CMU-TEC-001 Concrete Masonry Unit Shapes, Sizes, Properties, and Specifications, CMU basics dimensions and sizes
-
Checked
Source: How much extra tile to buy, How much overage for tile, Roofing Calculator: Squares, Bundles, Underlayment, ProSeries LVF installation and care guide, TDS 400 LATICRETE Grout Guide, TEK 04-02A Estimating Concrete Masonry Materials
Method note: common trade practice, not an official standard. Check the figure with your supplier.
Worked example: a forty foot wall
A wall 40 feet long and 8 feet high has 320 square feet of face. At 1.125 blocks per square foot that is 360 blocks exactly. With the default 5 percent waste you buy 378 blocks, and the wall is 12 courses high.
Block sizes and the mortar joint
A standard concrete block is nominally 8 by 8 by 16 inches. The block you hold is a little smaller, 7.625 by 7.625 by 15.625 inches, so that a 0.375 inch mortar joint fits inside the 8 by 16 inch module.
Because the joint is already inside the nominal face, the calculator does not add it again. Adding it twice would give fewer blocks than the wall needs. If you use another block, enter its nominal face height and length in the two block fields.
Mortar, grout fill, reinforcement, lintels and bond beams are not estimated here. Metric sizes convert at 0.3048 meters per foot.
How the block count is worked out
Find the wall area (length times height), take away the doors and windows, and multiply by the number of blocks that cover one square foot. Add your waste percentage and round up, because you cannot buy part of a block. The calculator also counts the courses (rows) from the wall height and the blocks in each course from the wall length, rounded up to allow a cut block at the end.
A standard block covers 0.888889 square foot of wall, so it takes 1.125 blocks per square foot, or 112.5 per 100 square feet before waste. With 5 percent waste the masonry association figure is 119 blocks per 100 square feet.
The steps of the worked example appear here.
Method and sources
A standard concrete block is nominally 8 by 8 by 16 inches, with an actual size of 7.625 by 7.625 by 15.625 inches so that a 0.375 inch mortar joint fits inside the module. Its nominal face covers 0.8889 square feet, which gives 1.125 blocks per square foot, or 112.5 blocks per hundred square feet. Net area is wall length times height minus openings. Blocks exactly are the net area times the blocks per square foot, and the number to buy adds the waste and rounds up. With a waste allowance of 5 percent the masonry association figure is 119 blocks per hundred square feet. Metric entries convert at 0.3048 meters per foot.
What this calculator does not cover
- Waste percentages are common trade practice; adjust them to your project.
- Counts units for a plain wall; reinforcement, lintels, bond beams, bond pattern and mortar quantities are separate.
- The waste default is provisional, so check it with your block supplier.
Figures and calculation checked on Oct 11, 2026.
Related tools
Find the area of a rectangle, triangle, circle, ellipse, trapezoid, sector or polygon and read it in square feet, square yards, square meters and acres.
Frame a wood wall insteadCount the studs, plate lumber and boards for a wall from length, height and spacing, with the corner and opening allowances shown so you can change them.
Results are estimates for planning. Check quantities with your supplier, and local building codes or a qualified professional for anything structural.