Truss Calculator
Choose a truss type, enter the span, roof pitch, overhang and truss spacing, and the calculator returns the rise, top chord, bottom chord and web lengths and how many trusses fit along the building. These are centreline lengths for planning and budgeting. The actual truss is designed and built by a truss manufacturer.
See also: compare with stick-framed rafters
Checked Rules used
How the truss calculator works
Result
How it was calculated
Fill in the fields above to see the result and every step here.
- Checked Source: Roofing Calculator: Squares, Bundles, Underlayment
- Checked Source: Unit Conversion, Special Publication 811, Guide for the Use of the International System of Units, Handbook 44 (2026) Appendix C, General Tables of Units of Measurement, SP 811 Appendix B.8, Factors for units listed alphabetically, U.S. Survey Foot
Worked example: a king post truss
A king post truss with a 24 foot span, a 6 in twelve pitch and a 12 inch overhang has a rise of 72 inches. Each top chord is 161 inches before the tail and 174.4375 inches with the tail, the bottom chord is 288 inches and the centre web is 72 inches.
What only a truss engineer can supply
This page gives centerline geometry and a count, nothing else. It does not size any member, choose connector plates, plan the bracing or work out the loads, and it does not tell you whether a truss will carry a roof.
- The size and grade of lumber for every chord and web.
- The connector plates, their size and where they go.
- The loads for your site, such as roof, ceiling, snow and wind, and what your local code requires.
- Bracing, bearing, heel height and any camber.
Trusses are designed, stamped and supplied by a truss manufacturer. Treat the count and the lengths here as a budget figure and a way to talk to the supplier, not as a design.
How the truss lengths are worked out
The rise is half the span times the pitch over 12. Each top chord, measured along the slope from the heel to the peak, is the run (half the span) times the slope factor, sqrt(1 + (rise/12)^2). The tail adds the level overhang times the same factor. The bottom chord runs the full span. If you give a spacing and a building length, the truss count is the length divided by the spacing, rounded up, plus one for the end truss.
The web lengths follow a drawn layout for each type, from the centerlines. A king post truss has one vertical web as tall as the rise. A fink truss is a W: its bottom chord has panel points a third of the span from each end, the top chords have a panel point at their middle, and four webs join them. That layout is a drawing convention, not an engineered design. Lengths are shown to the nearest 1/16 inch, using 0.0254 meters per inch for metric entries.
The steps of the worked example appear here.
Method and sources
The rise is half the span times the pitch over twelve, and the top chord along the slope is the run times the slope factor, which is 1.118 for a pitch of six in twelve (sqrt(1 + (rise/12)^2)). The bottom chord runs the full span. The truss count is the building length divided by the spacing, plus one for the end truss. Web lengths follow a drawn layout convention for each type. Nothing on this page sizes a member, a connector plate or the bracing.
What this calculator does not cover
- Centreline geometry only. No member sizes, connector plates, bracing or load design.
- Trusses are engineered by the manufacturer; treat the truss count and the lengths as a budget figure, not a design.
- Web layouts for types such as the fink follow a drawn convention and are not engineered.
Figures and calculation checked on Oct 11, 2026.
Truss calculator FAQ
How do you build a roof truss?
This page does not give building steps. A roof truss carries load through engineered members and connector plates, so it is designed and built by the truss manufacturer to your plans. Use the lengths and the count here to plan and budget, then ask a manufacturer or an engineer for the real design.
Related tools
Find the area of a rectangle, triangle, circle, ellipse, trapezoid, sector or polygon and read it in square feet, square yards, square meters and acres.
Add several roof sections in square feetAdd rooms in feet and inches, subtract cut-outs, and get total square feet, square yards, square meters, an order quantity with waste and a cost.
Results are estimates for planning. Check quantities with your supplier, and local building codes or a qualified professional for anything structural.