Material Calculator
Choose concrete, a bulk material such as gravel or mulch, or paint, enter the size of the area and a waste percentage, and the calculator returns the cubic yards, bags, tons or gallons to buy, rounded up. Bag size, gravel weight, coats and paint coverage are visible inputs you can change, and the result prints as a shopping list.
See also: measure the area before you buy
Checked Rules used
Method note: common trade practice, not an official standard. Check the figure with your supplier.
How the material calculator works
Result
How it was calculated
Fill in the fields above to see the result and every step here.
My shopping list
Press "Add to my list" under the result of any calculator on this site, then print everything once. The list stays in this browser only.
Nothing on your list yet. Work out a material above or on any tile, flooring, stud, roofing or block page, then press "Add to my list".
Waste on each line is the percentage you chose. Defaults come from constr.waste_factors and constr.bulk_material, checked 2026-10-11.
-
Checked
Source: Concrete Mix No. 1101 product data sheet, SuperPaint Interior Latex Flat A86 Series product data sheet 101.02A, Handbook 44 (2026) Appendix C, General Tables of Units of Measurement
Method note: common trade practice, not an official standard. Check the figure with your supplier.
- Checked Source: Unit Conversion, Special Publication 811, Guide for the Use of the International System of Units, Handbook 44 (2026) Appendix C, General Tables of Units of Measurement, SP 811 Appendix B.8, Factors for units listed alphabetically, U.S. Survey Foot
-
Checked
Source: How much extra tile to buy, How much overage for tile, Roofing Calculator: Squares, Bundles, Underlayment, ProSeries LVF installation and care guide, TDS 400 LATICRETE Grout Guide, TEK 04-02A Estimating Concrete Masonry Materials
Method note: common trade practice, not an official standard. Check the figure with your supplier.
Worked example: a slab in bags
A slab ten feet by ten feet and four inches deep is 1.235 cubic yards. With bags that yield 0.6 cubic feet each and no waste, you need 56 bags.
The yield table behind the numbers
Every quantity here rests on a few figures you can see and change. A cubic yard is 27 cubic feet exactly. An 80 lb bag of one common concrete mix yields about 0.6 cubic feet. Divide your volume in cubic feet by the yield and round up to get the bags. Other mixes yield a little more or less, so read the bag.
The steps of the worked example appear here.
Product yield and waste table
How much one bag, bundle, block or gallon covers, and the waste people usually add. Figures marked Common practice are typical values, not a standard: check the package or ask your supplier. Checked Oct 11, 2026.
| Product | Figure | Status | Source and note |
|---|---|---|---|
| Concrete, 80 lb bag | 0.6 cu ft per bag | Confirmed | One manufacturer's data sheet. Other products and bag sizes differ: you can change the yield in the calculator. QUIKRETE |
| Cubic yard | 27 cu ft | Confirmed | Exact definition. NIST |
| Mulch bag | 2 cu ft per bag, 13.5 bags per cu yd | Common practice | A typical bag size, not sourced. Read the bag. |
| Gravel | 1.4 tons per cu yd | Common practice | Typical value; real stone varies with the stone type and its moisture. |
| Interior paint | 350 sq ft per gallon, 2 coats | Common practice | The low end of one manufacturer's stated range. Check the can. Sherwin-Williams |
| Roofing square | 100 sq ft per square, 3 bundles per square | Common practice | Confirmed on one shingle data sheet; other products use 3, 4, 5 bundles per square. Check the package. IKO IKO |
| Concrete block (8 by 8 by 16 in) | 1.125 blocks per sq ft, 112.5 per 100 sq ft | Confirmed | The joint is already inside the nominal size. 119 per 100 sq ft with 5% waste. Concrete Masonry and Hardscapes Association (formerly NCMA) Concrete Masonry and Hardscapes Association (formerly NCMA) |
| Material | Waste | Status | Source and note |
|---|---|---|---|
| Tile | 10% straight, 15% diagonal or complex | Common practice | Common trade practice; no tile standard states it. |
| Flooring planks | 10% straight, 15% diagonal | Confirmed | From a flooring manufacturer's installation guide. Daltile |
| Grout | 10% | Confirmed | From a grout manufacturer's data sheet. LATICRETE |
| Roofing shingles | 10% (10 to 15% typical, up to 20% on a complex roof) | Common practice | Common trade practice. |
| Wall studs | 0% default, 5 to 10% suggested | Common practice | Convention; crooked boards and cuts vary. |
| Concrete block | 5% (5 to 10% suggested) | Confirmed | From the masonry association's estimating guide. Concrete Masonry and Hardscapes Association (formerly NCMA) |
| Concrete | 10% | Common practice | Convention for spills and uneven ground. |
| Gravel, sand, mulch and soil | 5% | Common practice | Convention. |
Read from constr.bulk_material, constr.roofing, constr.cmu_block and constr.waste_factors. A product data sheet that says something different wins: change the figure in the calculator.
Gravel and other loose stone is sold by the ton. A typical figure is 1.4 tons per cubic yard, but it changes with the kind of stone and with moisture, so ask your supplier for theirs. A bag of mulch is typically 2 cubic feet, which is 13.5 bags to the cubic yard.
Paint covers about 350 square feet a gallon, the low end of the range on one maker's data sheet, and we start with 2 coats. Porous or dark walls take more. The can label wins over our number.
Method and sources
Concrete and bulk volume is length times width times depth, turned into cubic yards by dividing cubic feet by 27. Bags are the volume in cubic feet divided by the yield per bag, rounded up; the default yield of an eighty pound concrete bag is 0.6 cubic feet. Gravel tons use 1.4 tons per cubic yard as a typical figure, and a mulch bag is typically 2 cubic feet. Paint is the area times the number of coats divided by the coverage per gallon, with 350 square feet per gallon and 2 coats as defaults, rounded up to whole gallons. The paint figure is the low end of the range on one manufacturer data sheet.
What this calculator does not cover
- Waste percentages are common trade practice; adjust them to your project.
- Gravel weight and mulch bag size are typical values; ask your supplier.
- Flat rectangular areas only; slopes, irregular footings and wall paint with openings need the specific page or a manual subtraction.
- Bag yield, gravel weight, mulch bag size and paint coverage defaults are provisional typical values, so check the label on the product you buy.
Figures and calculation checked on Oct 11, 2026.
Material calculator FAQ
How much material do I need?
Choose what you are buying, enter the area and depth, and read the amount to buy after waste. A slab ten feet by ten feet and four inches deep is 1.235 cubic yards, or 1.36 cubic yards with 10 percent waste.
How do you use a material estimator?
Pick concrete, bulk material or paint. Enter the dimensions in feet and the depth in inches. Leave the waste, bag size and coverage at their defaults or change them to match the label on the product you are buying. Read the quantity to buy, then print the list to take to the store.
How much gravel or paint do I need?
For gravel, a bed 20 by 10 feet and 3 inches deep with 5 percent waste needs 1.94 cubic yards, about 2.72 tons. For paint, 800 square feet with 2 coats at 350 square feet per gallon needs 4.57 gallons, so buy 5.
Related tools
Find the volume of a box, cylinder, sphere, cone, pyramid or pipe wall and read it in cubic feet, cubic yards, liters and gallons, with the formula shown.
Estimate shingle bundles for a roofTurn a roof footprint and pitch into roof area, roofing squares and whole shingle bundles, with the slope factor and waste shown and a list to print.
Results are estimates for planning. Check quantities with your supplier, and local building codes or a qualified professional for anything structural.