Stud Calculator
Enter the wall length and height, the stud spacing, the number of corners and openings and a waste percentage. The calculator returns the studs in the field, the extra studs for corners and openings, the studs to buy, the plate lumber in linear feet and boards, and the stud cut length. The allowances are shown and can be changed.
See also: find the wall area first
Checked Rules used
Method note: common trade practice, not an official standard. Check the figure with your supplier.
How the stud calculator works
Result
How it was calculated
Fill in the fields above to see the result and every step here.
-
Checked
Source: IRC 2021 R602.3.2 Top plate
Method note: common trade practice, not an official standard. Check the figure with your supplier.
-
Checked
Source: How much extra tile to buy, How much overage for tile, Roofing Calculator: Squares, Bundles, Underlayment, ProSeries LVF installation and care guide, TDS 400 LATICRETE Grout Guide, TEK 04-02A Estimating Concrete Masonry Materials
Method note: common trade practice, not an official standard. Check the figure with your supplier.
Worked example: a wall with openings
A wall 20 feet long and 8 feet high with studs at the default 16 inch spacing needs 16 studs in the field. 2 corners add 4 studs and 3 openings add 12, which gives 32 studs before waste and 36 to buy with 10 percent waste. The plates need 60 linear feet, or 8 boards, and each stud is cut to 91.5 inches.
Spacing, corners and openings
Studs go 12, 16, 19.2, 24 inches apart, measured on center, and 16 inches is the usual choice. The spacing for your wall comes from your plans and local code, so use the one they say.
Each corner adds 2 studs, and each window or door adds 4 studs for the king and jack studs at its sides. These are common framing habits. Building codes do not set stud counts, and framers differ, so treat them as a starting count.
Not counted: headers, cripple studs, sills, blocking and fire stops. Add those from your plans.
How the stud count is worked out
Studs in the field are the wall length in inches divided by the spacing, rounded up, plus one for the end stud. That is written ceil(length_ft*12/spacing)+1. Corners and openings add studs on top, and the waste you choose is applied to the total and rounded up, so you end with a whole number of studs to buy.
The plates are one bottom plate and a double top plate, which is three times the wall length in lumber. Each stud is cut shorter than the wall by the three plate thicknesses of 1.5 inches each. The calculator counts plate boards of the length you pick and rounds up.
The steps of the worked example appear here.
Method and sources
Studs in the field are the wall length in inches divided by the spacing, rounded up, plus one, written ceil(length_ft*12/spacing)+1. Each corner adds 2 studs and each opening adds 4 studs by framing convention. Waste is applied to the total and rounded up. Plates are a double top plate and a single bottom plate, each 1.5 inches thick, and the stud cut length is the wall height minus the three plate thicknesses. Spacing options are 12, 16, 19.2 and 24 inches on centre, with 16 as the default. Lengths in feet use the international foot, 0.3048 meters per foot.
What this calculator does not cover
- Waste percentages are common trade practice; adjust them to your project.
- Stud counts and corner and opening extras are common framing practice, not code requirements.
- Framing allowance for a straight wall; a real take-off follows the plans and your local code.
Figures and calculation checked on Oct 11, 2026.
Stud calculator FAQ
How many studs do I need?
Divide the wall length in inches by the spacing, round up and add one, then add the corner and opening allowances. A wall 20 feet long at the default 16 inch spacing needs 16 studs, and at 24 inch spacing it needs 11.
Related tools
Count the concrete blocks for a wall from length, height and openings, using the real nominal module, with waste added and rounded up to whole blocks.
Estimate paint for the finished wallEstimate concrete bags, gravel or mulch, and paint gallons to buy, with a visible waste percentage, rounded-up quantities and a printable shopping list.
Results are estimates for planning. Check quantities with your supplier, and local building codes or a qualified professional for anything structural.