Roofing Square Calculator
Enter the building footprint, or its length and width, with the roof overhang, the pitch as rise per twelve and a waste percentage. The calculator applies the slope factor to the footprint, returns the roof area in square feet and in roofing squares, adds waste and rounds up to whole bundles, with the slope factor and the waste shown.
See also: find the area of a single roof plane
Checked Rules used
Method note: common trade practice, not an official standard. Check the figure with your supplier.
How the roofing square calculator works
Result
How it was calculated
Fill in the fields above to see the result and every step here.
- Checked Source: Roofing Calculator: Squares, Bundles, Underlayment
-
Checked
Source: How many bundles of shingles are in a square, Roofing Calculator: Squares, Bundles, Underlayment, Cambridge technical data sheet (11/2023 on sheet), Bundles of IKO shingles in a square (manufacturer page)
Method note: common trade practice, not an official standard. Check the figure with your supplier.
-
Checked
Source: How much extra tile to buy, How much overage for tile, Roofing Calculator: Squares, Bundles, Underlayment, ProSeries LVF installation and care guide, TDS 400 LATICRETE Grout Guide, TEK 04-02A Estimating Concrete Masonry Materials
Method note: common trade practice, not an official standard. Check the figure with your supplier.
Worked example: a gable roof
A footprint 40 feet by 30 feet at a 6 in twelve pitch has a slope factor of 1.118, so the roof area is 1,341.6 square feet, or 13.42 squares. With 10 percent waste that is 14.76 squares. At 3 bundles per square you buy 45 bundles.
Slope factor by pitch
A sloped roof is bigger than the footprint under it. The slope factor says how much: sqrt(1 + (rise/12)^2). A 6/12 roof has a factor of 1.118034, so the roof area is that much more than the footprint. A flat roof has a factor of 1.
| Pitch | Slope factor | Pitch | Slope factor | Pitch | Slope factor |
|---|---|---|---|---|---|
| 1/12 | 1.0035 | 9/12 | 1.2500 | 17/12 | 1.7341 |
| 2/12 | 1.0138 | 10/12 | 1.3017 | 18/12 | 1.8028 |
| 3/12 | 1.0308 | 11/12 | 1.3566 | 19/12 | 1.8727 |
| 4/12 | 1.0541 | 12/12 | 1.4142 | 20/12 | 1.9437 |
| 5/12 | 1.0833 | 13/12 | 1.4743 | 21/12 | 2.0156 |
| 6/12 | 1.1180 | 14/12 | 1.5366 | 22/12 | 2.0883 |
| 7/12 | 1.1577 | 15/12 | 1.6008 | 23/12 | 2.1619 |
| 8/12 | 1.2019 | 16/12 | 1.6667 | 24/12 | 2.2361 |
Lengths in meters convert at 0.3048 meters per foot.
How the bundles are counted
A roofing square is 100 square feet of roof. Start with the footprint of the building, including any overhang on each side, and multiply it by the slope factor to get the roof area. Divide by 100 for squares, add your waste, then multiply by the bundles in one square and round up to whole bundles.
Common waste is 10 to 15 percent, and up to 20 percent for a complex roof with many planes, dormers and valleys. The default is 3 bundles per square, and the page also offers 4 and 5. Bundles per square depend on the shingle, so the package label decides.
This counts the shingles only. Starter, ridge and hip cap bundles, underlayment and flashing are separate lines.
The steps of the worked example appear here.
Method and sources
Roof area is the footprint, including any overhang on each side, times the slope factor from the formula sqrt(1 + (rise/12)^2). For a pitch of six in twelve the factor is 1.118. One roofing square covers 100 square feet. Squares with waste are the squares times one plus the waste, and bundles are those squares times the bundles per square, rounded up. The default is 3 bundles per square, and the page also offers 4 and 5. Common waste is 10 to 15 percent, and up to 20 percent for a complex roof. Metric entries convert at 0.3048 meters per foot.
What this calculator does not cover
- Waste percentages are common trade practice; adjust them to your project.
- Bundles per square vary by shingle product; check the package.
- Simple gable or hip footprint estimate; many planes, dormers and valleys raise waste.
- The default of three bundles per square is confirmed for one manufacturer product only. The other options are not yet confirmed, so the package label decides.
Figures and calculation checked on Oct 11, 2026.
Related tools
Find the cut length of a common rafter from span, pitch, overhang and ridge board thickness, with the cut angles and a rafter count.
Plan the truss lengths and countGet the rise, top and bottom chord lengths, web lengths and the number of trusses along a building from span, pitch, overhang and spacing, for planning.
Add several roof sectionsAdd rooms in feet and inches, subtract cut-outs, and get total square feet, square yards, square meters, an order quantity with waste and a cost.
Results are estimates for planning. Check quantities with your supplier, and local building codes or a qualified professional for anything structural.